【正文】多零件加工-X方向                                                      G75W_Q_                                                               W:宏編號                                                              Q:加工起始位置                                                         在命令多選配置時,處理X方向上的分配程序 多零件加工-Y方向                                                      G76W_Q_                                                               W:宏編號                                                              Q:加工起始位置                                                        在命令多選配置時,處理Y方向上的分配程序 沖切弧                                        G78I_J_K_P_Q_D_T_C_                          I:半徑                         Q:間距          J:起始角度                     D:板厚            K:加工角度                     T:模具#          P:模具直徑                     C:旋轉工位角         在弧中僅允許固定角度, 以等距離間隙沖切  沖切線                                                                G79I_J_P_Q_D_T_C_                                                                                                                           I:加工長度                                                            J:角度                           D:板厚                       P:模具直徑                       T:模具#                    Q:間距                           C:旋轉工位角          在直線中僅允許固定距離,以等距離間隙沖切 2英吋分度刻印                                                         G80X_Y_I_J_K_P_Q_T_                                                   X:起始刻印X坐標                                                        Y:起始刻印Y坐標                                                       I:刻印起始信息(第1--第4字符)                                          J:刻印起始信息(第5--第8字符)                                          K:刻印起始信息(第9-第12字符)                                           P:刻印X方向間距                                                       Q:刻印Y方向間距                                                       T:模具#                                                               對于分度刻印使用2 英吋G 代碼 1_1/4英吋分度刻印                                                      G81X_Y_I_J_K_P_Q_T_                                                   X:起始刻印X坐標                                                       Y:起始刻印Y坐標                                                       I:刻印起始信息(第1--第4字符)                                           J:刻印起始信息(第5--第8字符)                                          K:刻印起始信息(第9-第12字符)                                          P:刻印X方向間距                                                       Q:刻印Y方向間距                                                        T:模具#                                                               對于分度刻印使用1 1/4 英吋G 代碼 絕對程序選擇(絕對坐標命令)                                            G90X_Y_T_C_                                                           X:X 坐標                                                              Y:Y 坐標                                                              T:模具#                                                               C:旋轉工位角                                                           當坐標值使用絕對值時,先鍵入G90                                        到坐標值.                                                             如果子程序塊使用絕對值                                                將不需要再輸入"G90"                                                    直到相對值被使用.如果"G90/G91"不存在于程序中,                         缺省將為"G90". 相對程序選擇(相對/增量)                                               G91X_Y_T_C_                                                           X:X 移動量                                                             Y:Y 移動量                                                            T:模具#                                                               C:旋轉工位角                                                          當坐標值使用相對值時,先鍵入                                            "G91" 到坐標值.                                                       如果子程序塊使用相對值                                                將不需要再輸入"G91"                                                   直到絕對值被使用. 坐標設定(原點設定)                                                     G92X_Y_                                                               X:機床原點-X 值                                                       Y:機床原點-X 值                                                       在設置機床參數中輸入機床原點.                                          輸入值是機床的樣本,因為它是通用的.                                    從此命令內,X/Y 坐標原點將判定"X0,Y0"                                  此設定坐標中, 所有的絕對命令在程序內是有效的 本地坐標設定                                                          G93X_Y_                                                                X:偏置坐標-X                                                          Y:偏置坐標-Y                                                          移動NC原點與X/Y 坐標值對齊.                                           當執行此命令時,所有后面的絕對坐標將平行移動                           在命令塊"G93"中,正好復位原來的內NC,                                   機床軸運動和板面處理將不能運轉.                                       在"G93"塊中, 不是"G90/G91/N/X/Y"的命令代碼                            不能執行      多零件加工- 坐標設定                     I:X 軸方向間隔                G98X_Y_I_J_P_K_                          J:Y 軸方向間隔                X:基準點坐標-X值                         P:X 軸方向量                 Y:基準點坐標-Y值                         K:Y 軸方向量                安排位置在"X_Y_"需要左下產品的本地原點                                 請指令"I_J_P_K_"的每一值為"0"和"正"