【正文】直線運動結束                                                          G00                                                                   取消直線運動命令                                                      在這個命令后, 返回垂直軸運動命令                                       當切槽加工以任意角度時給出直線移動命令                                在其它時間請不要使用                                                 

直線運動開始          G01F_                                                                 F:加工速度                                                             直線移動的起始命令.                                                   遵照加工速度F, 做直線移動的軸運動.                                    "G01" 是有效模塊直到"G00"被取消.                                      當切槽加工以任意角度時給出直線移動命令                                在其它時間請不要使用                                                  F 地址 不可遺漏.                                                      在"G01" 和 "G00"期間不能使用T/C 命令.      

閉鎖                                                                  G04X_                                                                  X:閉鎖時間                                                             僅機床停止動作軸運動需要時間.                                        在X地址內停止時間以'秒'為單位.                                       如需要,請指令單一塊.                                                

夾具定位器命令                                                        G05I_J_K_                                                             I:夾具1 位置(100.00<=I<=1480.00)                                      J:夾具2 位置(350.00<=J<=1730.00)                                       夾具1 和 夾具2 間隔(>=250.00)                                       K:當夾具移動時的加工選擇                                               K0:材料設置                                                          K1:死區避讓(與G25相同)                                                K2:死區避讓(與G27相同)                                              在G05前請不要輸入裝入命令 材料設定(板厚/材料類型代碼)                                           G06A_B_                                                               A:板厚                                                                B:材料類型編號                                                         0:SPC(鋼)                                                            1:SUS(不銹鋼)                                                         2:AL(鋁)                                                            請在程序頭給出"G06"塊                                                 當"G06" 未設定材料時,板厚6.3mm/材料類型0:SPC                          被自動設置                                  

卸載命令                                                               G10X_                                                                 X:材料X方向尺寸                                                       當L-UL附著時材料的卸載命令                                            輸入材料的X方向尺寸

材料載出命令                                                          G10X_Y_Q_M_                                                           X:材料 X 尺寸                                                         Y:材料 Y 尺寸                                                          Q:真空 方法                                                            (0:Pad/1:電磁/2:Pad + 電磁/3:夾具)                                   M:卸載器種類                                                          串聯設備類型在取出內部,取出類型可以指示
在三菱(松下)環境下.

對于板面加工的構架或微連接指令                                        G10X_Y_M_                                                             X:板料X-尺寸                                                          Y:板料Y-尺寸                                                           M:對于構架板面指令到擱板托盤                                          僅允許:                                                                  1) L/UL 類型取出                                                      2) 取出類型是"Tsukata" 或 "Ookuma"