切割工藝參數子程序說明
發布時間：2019-05-08 17:20:42 | 人感興趣 | 評分：3 | 收藏：
【正文】切割工藝參數設定子程序說明(例Q900303)：
N1010 (3MM MILD D=1.4 S=5.0 F=1)
N1020
N1030 (cut1_param)
*N1040 P100=3500 /...(3500)......mm/min；feedrate
*N1050 P101=00 /...(00)......w，laser power
*N1060 P102=90 /...(90)..........percent of Pmin
*N1070 P103=1 /...(1)............1-2，1=CW；2=GATE
*N1080 P104=0 /...(0)............0-7，pulse freq
*N1090 P106=1.0 /...(1.0).........mm，nozzle height
*N1100 P107=2.5 /...(2.5)..........bargas pressure
*N1110 P108=2 /...(2)............1=AIR，2= O2，3= N2，gas type
*N1120 P109=1 /...(1)............0=no， 1=yes；whether to lift
N10
N1140 (pierce_param)
*N10 P110=1 /...(1).............0-3；0=no；1=norm；2=incrf；3=force
*N1160 P111=500 /...(500)......w，laser power
*N1170 P1=3 /...(3).............1-4，1=CW；2=GATE；3=SP；4=HY
*N10 P114=0 /...(0).............0-7，pulse freq
*N1190 P116=3 /...(3).............mm，nozzle height
*N1200 P117=1.5 /...(1.5).............bar，gas pressure
*N1210 P1=2 /...(2).............1=AIR，2= O2，3= N2，gas type
*N1220 P119=800 /...(800).........ms，pierce timer
N1230
N1240 (share_param)
*N1250 P0=1 /...(1).............0=no，1=yes； whether to follow
*N1260 P1=0 /...(0).............0=no，1=yes； whether to prepierce
*N1270 P2=30 /...(30)...........mm，z axis lift height
*N1280 P3=90 /...(90)........1-100%； dynamic factor
*N1290 P4=600 /...(600)...........ms，cut_start_timer
*N00 P5=10 /...(10)...........ms，cut_finish_timer
*N10 P6=00 /...(00)...........ms，mark_start_timer
*N20 P7=00 /...(00)...........ms，close_gas_timer
N25
N30 (corner_param)
*N40 P170=0 /...(0)............0=no，1=yes； enable corner lowspeed
*N50 P171=100 /...(100)........percent of lowspeed
*N60 P172=0 /...(0)............ms；corner_timer
N70
N80 (downlead_param)
*N90 P120=0 /...(0).............0-3；0=NO；1=HOLE；2=DECS；3=1+2
*N1400 /cut_hole
*N1410 P121=1200 /...(1200)......w，laser power(HOLE)
*N1420 P122=1000 /...(1000).....mm/min；feedrate(HOLE)
*N1430 P123=1 /...(1)...........1=CW，2=GATE(HOLE)
*N1440 P124=0 /...(0)...........0-7，pulse freq(HOLE)
*N1450 P126=2 /...(2)...........mm，nozzle height(HOLE)
*N1460 P127=3 /...(3)...........bar，gas pressure(HOLE)
*N1470 P128=2 /...(2)...........1=AIR，2= O2，3= N2，gas type(HOLE)
*N1480 /lowspeed_start
*N1490 P177=100 /...(100).......percent OF lowspeed(DECS)
*N00 P178=0 /...(0)...........mm，distance of lowspeed(DECS)
*N10 P179=0 /...(0)............mm，nozzle-off of lowspeed(DECS)
N20
N30 (cut2_param)
*N40 P140=3000 /...(4000).....mm/min；feedrate
*N50 P141=1200 /...(1200).....w；laser power
*N60 P142=90 /...(90)..........percent of Pmin
*N70 P143=1 /...(1)...........1-2，1=CW；2=GATE
*N80 P144=0 /...(0)...........0-7，pulse freq
*N90 P146=1.0 /...(1.0)........mm，nozzle height
*N1600 P147=1.2 /...(1.2)...........bar，gas pressure
*N1610 P148=2 /...(2)...........1=AIR，2= O2，3= N2，gas type
*N1620 P149=1 /...(1)...........0=no， 1=yes；whether to lift
N1630
N1640 (cut3_param)
*N1650 P0=500 /...(500).....mm/min；feedrate
*N1660 P1=00 /...(00).....w，laser power
*N1670 P2=80 /...(80)..........percent of Pmin
*N1680 P3=1 /...(1)............1-2，1=CW；2=GATE
*N1690 P4=1 /...(1)............0-7，pulse freq
*N1700 P6=1.0 /...(1.0)........mm，nozzle height
*N1710 P7=2.5 /...(2.5)............bar，gas pressure
*N1720 P8=2 /...(2)............1=AIR，2= O2，3= N2，gas type
*N1730 P9=1 /...(1)............0=no， 1=yes；whether to lift
N1740
N1750 (mark_param)
*N1760 P160=5000 /...(5000).....mm/min；feedrate
*N1770 P161=400 /...(400).......w，laser power
*N1780 P162=50 /...(50).........percent of Pmin
*N1790 P163=1 /...(1)...........1-2，1=CW；2=GATE
*N00 P164=0 /...(0)...........0-7，pulse freq
*N10 P166=5 /...(5)...........mmnozzle height
*N20 P167=3 /...(3)...........bar，gas pressure
*N30 P168=1 /...(1)...........1=AIR，2= O2，3= N2，gas type
*N40 P169=1 /...(1)...........0=no， 1=yes；whether to lift
N50
N60 (proc_end)
N70 M02
您看到此篇文章時的感受是：
